Nov 20, 2026Leave a message

Linear Block Bearings: Types, Preload and How to Size Them

A linear block is the carriage that runs on a linear guide rail. Choosing one is mostly arithmetic: load, life, preload and accuracy grade, in that order. Most selection errors happen because buyers start with the size number instead of the load case. This guide walks through the sequence in the order that avoids rework.

What "Linear Block" Means in Practice

The terminology trips people up because the same component is sold under several names: linear block, linear bearing block, carriage, slider, and in profile-rail systems simply "block". In all cases it means the same thing - the recirculating bearing element that runs along a rail and carries the moving load.

Two broad families exist:

  • Profile rail blocks. A block wraps a rail with a matching ground profile. Four rows of balls or two rows of rollers run in ground raceways. These carry load in every direction, including moment loads, without external support.
  • Round shaft bearings. A block or bushing runs on a hardened round shaft, usually with two shafts per axis. Cheaper, more forgiving of misalignment, but each shaft carries load in essentially one direction.

This article deals with profile rail blocks, because that is where the selection arithmetic matters and where the wrong choice is expensive.

Square or Flange: The First Decision

Profile rail blocks come in two body shapes, and the choice is mechanical, not aesthetic.

Square block

The mounting face and the body are close to the same width. Bolt holes come in from the top, and usually from the bottom as well. Square blocks are stiffer for a given size and are the default when the block bolts down onto a flat carriage plate.

Flange block

The body is narrower than the mounting flange, which overhangs to one side. Used when the block has to be bolted to a vertical face or where space above the block is limited. Flange blocks give more mounting freedom but less torsional stiffness, and the overhang is a lever arm that has to be included in the moment calculation.

Both shapes are available in the same rail size, so a 25 rail can carry either a square or a flange block. What is not interchangeable is the rail itself - blocks and rails must come from the same series.

Reading the Size Number Correctly

The number in the part code is the nominal rail width in millimetres, not the block width and not the load rating. A 25 series block runs on a 25 mm wide rail.

Within one rail size there are usually two or three block variants - differing in body length (normal, long, short) and in mounting style. A long block of the same rail size carries noticeably more load and resists moment better than a standard block, because the ball rows are further apart.

This is the single most useful fact in block selection: when you are short of load capacity, a longer block of the same rail size is often cheaper than going up a rail size. Going up a size means new rail, new mounting height and usually a redesign of the carriage plate. A long block often drops into the same envelope.

Dynamic Load, Static Load and the Safety Factor

Two ratings are printed on every datasheet, and they answer different questions.

  • C, dynamic load rating. The load at which 90 percent of a population reaches 50 km of travel. This is the number used for life calculation.
  • C0, static load rating. The load that permanently deforms the raceway by a defined small amount. This is the number used to check that the block will not be brinelled while stationary or during a crash.

The static safety factor is simply fs = C0 / P, where P is the actual load on the most heavily loaded block. Typical minimums:

Application Minimum static safety factor fs
Smooth, vibration-free, indoor 3
General machinery with normal shock 4
Machine tools, frequent start-stop 5
Presses, punch presses, heavy impact 7 or higher

If fs lands below the band for your application, the block will not fail gracefully - it will develop indentation marks in the raceway and start to feel notchy long before it wears out. Raceway brinelling is permanent and cannot be lubricated away.

Preload: Z0, ZA, ZB and What They Cost You

Preload is the internal interference between the balls and the raceways. It trades friction for rigidity.

Class Condition Typical use
Z0 / ZF Clearance or very light preload Conveyors, handling, vertical axes with counterbalance
ZA Light preload General automation, pick-and-place
ZB Medium preload Machining axes, high-rigidity requirements

The trade is direct: more preload means less deflection under load and a stiffer axis, but higher running friction, more heat, and shorter life for the same load. On a lightly loaded axis, fitting ZB preload to gain stiffness you never use will simply shorten the block's life and raise the motor current.

A practical rule: choose the lightest preload that keeps deflection within your accuracy budget. Do not choose preload to fix a structural problem - if the carriage plate flexes, a stiffer block will not save it.

Accuracy Grades and What They Actually Control

Blocks and rails are graded for running parallelism and height variation. Grades run roughly from C (normal) through H, P, SP and UP (highest). The grade controls how closely two blocks on the same rail sit at the same height, and how much the rail deviates from a straight line over its length.

Two blocks on one rail at a low grade can differ in height by enough to twist a rigid carriage plate. If your application uses two rails and four blocks and the plate is rigid, the accuracy grade matters far more than it does on a single-rail, single-block axis. Match the grade to the geometry, not to a wish for precision.

Life Calculation You Can Do by Hand

For ball-type profile blocks, the standard life equation is:

L = (C / P)³ × 50 km

where L is the travel life in kilometres, C the dynamic load rating and P the equivalent load on the block. Roller-type blocks use (C / P)^(10/3) × 100 km instead, which is why roller blocks last longer in heavy-load applications.

The number that catches people out is P. On a four-block carriage, P is not one quarter of the payload. It is the load on the single most heavily loaded block, and it includes the moment contribution whenever the centre of gravity is offset from the geometric centre of the four blocks. A gantry with the load hanging off one end can load one block several times more than its neighbours, and that block sets the life of the axis.

Compute P for each block separately, take the maximum, then run the equation.

Mounting Errors That Shorten Life

The block is usually blamed for failures caused by the mounting surface. Three errors dominate:

  • Rail and block mounting faces not coplanar. Forcing a rail down onto a twisted surface preloads the rail itself and the block runs tight in places and loose in others.
  • Shoulder height wrong. The reference shoulder that locates the rail must be square and at the right height; a burr or a rounded shoulder lets the rail sit at an angle.
  • Bolts tightened in sequence from one end. Snug all bolts first, then torque from the centre outwards, or the rail will bow.

FAQ

What is the difference between a linear block and a linear guide?

The guide is the system - rail plus block. The block is the moving carriage. In practice buyers use "linear guide" for the complete assembly and "linear block" for the carriage on its own, which is how our linear block page and the linear guide category are organised.

Can I use blocks from one brand on another brand's rail?

Sometimes, if both are made to the same interchangeable standard and both are within tolerance. It is not guaranteed, and mixing them voids any accuracy claim. Blocks and rails should be bought as a matched pair.

Should I choose a long block or a bigger size?

Start with the long block. It raises load capacity and moment resistance within the same rail size, with no change to mounting height. Move up a rail size only when the long block still does not meet the life target.

How much preload do I need?

The least that keeps deflection inside your accuracy budget. ZA suits most automation. Use ZB only when the process genuinely needs the rigidity, and accept the higher friction and shorter life that come with it. The HGR linear guide range lists which preload classes are available per size.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry