The blocks that fail early rarely fail from wear. They fail because grit got past the wiper, or because the grease that was applied at the factory was the last grease they ever saw. Both are service issues, and both are cheap to prevent.
What is inside the block, briefly
An HGR block runs recirculating balls in four contact rows, two on each side of the rail. The balls circulate through return paths in the end caps. A wiper at each end scrapes the rail as the block travels, and a seal behind the wiper keeps the grease in.
That is the whole mechanism. Everything that goes wrong follows from it: the balls need clean rail, the grease needs to stay where it was put, and the wiper is the only thing standing between the raceway and whatever is in the air.
Service by distance, not by calendar
Most maintenance schedules say "check monthly". That is the wrong unit. A block on a machine that runs eight hours a day, five days a week sees a completely different duty from the same block on a machine that runs two shifts.
Count distance travelled instead. A block running a 600 mm stroke at 40 cycles a minute covers a lot of rail in an hour, and the grease film does not care what the calendar says.
Rough ordering, from our experience with customer machines:
- Clean, dry, light duty - greasing at long intervals is fine, but do not skip the wiper check.
- Wood dust, MDF, carbon fibre - the wiper is doing heavy work. Inspect it every few weeks, not every few months.
- Coolant mist or grinding dust - the worst case. Contaminant plus moisture turns grease into a grinding paste. Short intervals, and consider a bellows cover.
- Plasma and laser cutting - the fine metallic dust is abrasive and it gets everywhere. Covered rails or a positive-pressure arrangement help more than any grease choice.

Grease: which one, and how much
A lithium-based grease in the NLGI 2 range is the ordinary answer for HGR blocks, and it covers most machine tool use. What matters more than the brand is consistency - do not alternate between greases with incompatible thickeners, because they can separate and leave the raceway dry.
How much: pump until fresh grease appears at the wiper, then stop. Over-greasing is a real failure mode. Excess grease has nowhere to go and pushes the seals outward, and once a seal lifts it does not reseat properly. You have converted a lubrication job into a rebuild.
If the block is fitted with sealed or capped grease ports, do not assume it needs grease from outside. Check the configuration before pumping anything in.
The wiper is the part that actually wears
Wipers are consumable and they are usually the cheapest part on the assembly. They are also the first thing to check when a block starts feeling rough.
Look for:
- a wiper lip that has gone hard or curled away from the rail
- a visible gap between wiper and rail when you shine a light along it
- scoring or bright polished marks on the rail in a band, which means something is dragging
Replace the wiper before it stops working, not after. A worn wiper lets grit in continuously, and once abrasive particles are inside the ball path the raceway is being lapped away every cycle. That damage does not reverse when you fit a new wiper afterwards.
Check the rail face before blaming the block
A block that runs rough is often a rail that is not flat, or a mounting face with a burr under it. Two blocks on one rail that feel different usually means the rail, not the blocks.
Quick check: clean the rail, run a straight edge along the top and side faces, and look for light gaps. Then loosen and re-torque the rail bolts from the centre outward. If the roughness moves or changes, the mounting face was the problem.
Also check for witness marks. A bright, polished band that does not span the full width of the raceway means the block is running at an angle to the rail, and that is a mounting or parallelism problem rather than a lubrication one.
Preload: do not mix codes
HGR blocks come in preload classes - Z0 for clearance or light preload, ZA and ZB for increasing preload. A block and a rail are matched at assembly.
This matters when replacing parts. Fitting a ZB block onto a rail that was matched to Z0 will feel tight and may not run at all. Fitting a Z0 block in place of a worn ZB will introduce clearance the machine never had, and the axis will show it as lost motion.
If you are replacing one block on a rail, tell the supplier the preload code and, if you have it, the original part number. If the code is not marked, measure the drag force on a good block and match it. When in doubt, replace block and rail as a set - it costs more and it removes a whole class of troubleshooting.
Three field checks that find most problems in ten minutes
| What you find | What it usually means | What to do |
Dry, dark grease at the wiper | Service interval too long for the duty | Clean, re-grease, shorten the interval Grit or metal particles in the old grease | Wiper worn, or no cover on an abrasive process | Replace wipers, add a cover or bellows Rough feel over part of the stroke only | Rail damage, or a mounting face not flat | Inspect the rail at that position, re-seat the rail Audible click or knock at reversal | Preload lost, or a ball path damaged | Measure drag force, compare to a good block Grease leaking from the end cap | Seal pushed out by over-greasing | Re-seat or replace the seal, stop over-greasing Block hot to the touch after a short run | Too much preload, or too little clearance for the speed | Check the preload code against the application
That last one catches people. A block that runs warm is not always under-lubricated. If it was replaced recently, it may simply be the wrong preload class for the fit.
When to stop maintaining and start replacing
If the rail has visible fretting, pitting or a scored band, no amount of grease helps - the raceway geometry is gone. If a block has perceptible play when you rock it by hand against the rail, the balls or the raceway are worn past recovery. If the axis repeats worse after re-greasing than before, the contamination has already done its work.
In those cases the honest answer is replacement, and it is usually faster than another round of servicing.
We cut the HGR series across the standard sizes, and the EGR and MGR miniature ranges cover the lighter and smaller machines where the same maintenance logic applies with shorter intervals. If a rail is being damaged by an abrasive process, the organ-type dust cover is cheaper than a new rail and worth fitting before the wear starts rather than after.
If you are unsure whether a block is recoverable, send a photo of the rail surface at the point where it feels rough, plus the block's part number and, if visible, the preload code. That is usually enough to say whether it is a service job or a replacement.






