Oct 29, 2026Leave a message

How to Troubleshoot a Ball Screw Failure

Start With the Symptom, Not the Part

When a ball screw starts to misbehave, the instinct is to order a replacement. That is expensive and often wrong. A ball screw is one link in a chain that includes the support bearings, the nut housing, the coupling, the guide rails and the control loop. Before you pull the screw out, find out which link actually moved.

Three measurements settle most cases: backlash at the nut, axial play at the bearing block, and torque draw at the motor. Take all three cold, then again after the axis has run for twenty minutes. A fault that only appears when warm points at preload or thermal growth rather than wear.

Backlash That Appears Overnight

Gradual backlash is wear. Backlash that shows up after a crash, a transport move or a rebuild is almost always mechanical loosening, not material loss. Check in this order:

  • Locknut torque on the support bearing. A nut that backed off half a turn produces measurable axial play with no wear at all.
  • Coupling clamp screws and key fit. A slipping coupling reads as backlash on the part but leaves the screw untouched.
  • Nut housing bolts. On a horizontally mounted axis these take the full reversing load.

Only if all three are tight does the play belong to the nut itself. At that point the question is whether the screw uses a single nut with a preload shim or a double nut. A DFU double-nut ball screw can be re-shimmed to restore preload. A single nut with worn ball tracks generally cannot.

Noise and Vibration Under Load

A healthy ball screw is quiet under load and slightly louder at high speed. A screw that gets louder specifically when the axis is cutting is telling you the load path is deflecting. A screw that clicks once per revolution has a damaged ball or a dented raceway at one point. A screw that whines continuously above a certain speed is approaching its critical speed, which is a sizing problem rather than a failure.

Isolate the source before blaming the screw. Disconnect the coupling, run the motor alone, then turn the screw by hand through the full stroke. Roughness felt by hand at one specific position is a local defect. Roughness everywhere is contamination or lubrication.

Uneven Wear on the Nut Raceway

Wear concentrated at one end of the stroke means the machine spends most of its time there, which is normal for many operations but worth checking against the duty cycle. Wear in a narrow band in the middle usually means the screw is sagging or the rails are not parallel to the screw axis, so the nut is being forced sideways.

Parallelogram error is the most under-diagnosed cause of premature ball screw failure. If the guide rails and the screw are not parallel within the mounting tolerance, every stroke bends the screw slightly and loads one side of the raceway. You will replace screws indefinitely until the alignment is corrected. Measure rail-to-screw parallelism across the full travel, not at the two ends.

Contamination: The Most Common Cause

In woodworking, casting, grinding and graphite machining, contamination beats every other failure mode. Chips enter the nut, get rolled between the ball and the raceway, and brinell the track. The damage is progressive and irreversible.

Signs of contamination damage: a gritty feel when turning by hand, grease that comes out dark and metallic, and wear that appears across the full stroke rather than at one point. Wiper seals help but do not stop fine dust. For dusty environments, bellows or a dedicated dust cover does more than any seal. If you already run a rail dust cover on the guides, extend the same protection to the screw.

Torque Rise and Motor Overload

Rising motor current on an axis that used to run cool can come from the screw, but check the simpler causes first: lubrication starvation, a failing support bearing, or a coupling that is binding rather than slipping. A dry ball screw can double its running torque before any surface damage appears, which means catching it at this stage is cheap.

Compare torque at low speed against the value recorded when the machine was commissioned. A trend matters more than an absolute number. If no baseline exists, measure a healthy axis of the same size on the same machine and use that as the reference.

When Repair Is Not Worth It

Rebuilding makes sense when the screw is straight, the raceway damage is light and local, and the nut can be re-preloaded. It stops making sense in four situations:

  • The screw has visible brinelling or spalling across a working band.
  • Straightness is out beyond the grade tolerance, so a rebuild will still run rough.
  • The nut is a single-piece design with no preload adjustment.
  • The screw is at the end of its calculated life and a second failure would stop production again.

In those cases, replacing the screw and correcting the underlying alignment or contamination problem costs less than a second rebuild. Replacing without fixing the cause is the expensive option, because the new screw will fail the same way.

Rebuild or Replace: The Decision Line

Symptom Most likely cause Check before ordering Decision
Play appeared suddenly Locknut, coupling or housing loosened Torque all three cold and warm Retighten, no parts
Click once per revolution Damaged ball or local raceway dent Turn by hand, listen at low speed Rebuild if local
Gritty feel across stroke Contamination Inspect grease for metal Replace nut, add protection
Wear in a narrow band Rail-to-screw misalignment Measure parallelism over full travel Fix alignment first
Whine above a speed Critical speed Compare to calculated limit Re-size, not repair
Torque climbing over weeks Lubrication or bearing Check lube cycle and bearing play Service, then re-measure

If your measurements point to replacement, send us the screw diameter, lead, overall length, end machining drawing and a photo of the damaged raceway. We will confirm the grade and nut configuration against what you are running now, so the new part drops in without re-machining the end supports. An SFU ball screw in the same size is usually a direct swap where the original used a standard single nut.

Frequently Asked Questions

How much backlash is acceptable on a ball screw?

For a preloaded nut, measurable backlash at the nut should be near zero. Any play you can detect with a dial indicator on the nut, with the screw held still, points to lost preload rather than normal clearance. Compare against the value recorded at commissioning rather than a single universal number.

Can a worn ball screw be re-balled instead of replaced?

Yes, if the raceway is not spalled and the screw is straight. Oversized balls restore preload on a lightly worn nut. It is a stopgap: once the track is brinelled, new balls simply wear faster.

Why did a new ball screw fail within months?

Almost always an installation cause: misalignment between rails and screw, contamination entering an unprotected nut, or a support bearing preloaded incorrectly. The screw is rarely at fault that early.

Does grease type affect failure rate?

It affects it more than most operators expect. Lithium-based greases are common, but high-speed axes and cleanroom applications often need lower-viscosity or cleanroom-rated lubricants. Wrong grease shows up first as rising torque, then as wear.

Talk to an Engineer

Send photos of the failed surface, the axis arrangement and the current part number. We will tell you whether the failure is in the screw or upstream of it, and what to change so the replacement lasts. Request a technical review.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry