GDZ80-2.0 Water Cooled Spindle 2.0 kW ER20
video

GDZ80-2.0 Water Cooled Spindle 2.0 kW ER20

2.0 kW water cooled round spindle, 80 mm body, ER20 collet, 24000 rpm at 400 Hz, 220 V or 380 V.
Send Inquiry
Add To Inquiry
Product Introduction

The GDZ80-2.0-ER20 is a 2.0 kW water cooled round spindle in an 80 mm body. It carries an ER20 collet on an M25×1.5 nose and runs to 24000 rpm at 400 Hz, on either 220 V single phase or 380 V three phase.

Overview

The 80 mm body is the size that fits a benchtop gantry without crowding the Z axis. The mounting flange measures 58.6 mm across, the spanner flat is S = 21 mm, and the body runs 235 mm from flange to the rear cap on the four-bearing build. Two builds exist: three bearings, or four for a longer service life under continuous duty. The three-bearing body is 25 mm shorter, which is the only dimensional difference you have to allow for in a fixture drawing.

Water cooling is what makes the 2.0 kW rating usable at 24000 rpm. The heat leaves through the jacket, not through the housing surface, so the spindle can hold speed in a cut that an air cooled body of the same diameter would have to back off from. That matters on a small machine, where the spindle is often the first part to reach its thermal limit.

Specifications

Model GDZ80-2.0-ER20
Power 2.0 kW
Speed 24000 rpm
Frequency 400 Hz
Voltage 220 V or 380 V
Current 8 A at 220 V / 5 A at 380 V
Collet ER20, nose thread M25×1.5
Spanner flat S = 21 mm
Body diameter Ø80 mm
Mounting flange Ø58.6 mm
Body length 235 mm (four-bearing build; three-bearing build is 25 mm shorter)
Cooling Water cooled
Bearing pack 3 or 4 bearings

What 2.0 kW buys you

An ER20 nose takes shanks up to 13 mm, so the tooling range runs from a 3.175 mm engraving bit to a 12 mm flat cutter. At 2.0 kW the spindle holds that 12 mm cutter in wood, MDF, acrylic and foam without stalling, and takes light passes in aluminium when the feed is matched to the flute count. It is not a steel spindle: deep cuts in steel belong on a larger body with a bigger bearing pack.

Where the 2.0 kW rating pays off is on a machine that would otherwise fit a 1.5 kW air cooled unit. The water jacket holds the rating through a long program, so the last part of a batch cuts the same as the first.

Cooling and installation

Two ports on the rear cap take the water circuit. Run the inlet at the lower port so the jacket fills from the bottom, keep the flow steady rather than intermittent, and vent the loop before the first cut. A spindle that runs warm at idle is usually a loop with air in it rather than a spindle problem.

Mount on the 58.6 mm flange with the four fixing screws, bring the collet up hand tight, then use the S = 21 flat when you torque the nut. Leave the rear cap clear: it carries the water ports and the electrical connector, and neither takes kindly to being used as a lever point.

Matching VFD

The spindle needs a drive rated above it, not equal to it: a 2.2 kW class VFD is the usual pairing for a 2.0 kW spindle, set to 400 Hz and to the spindle's rated current rather than to its power. Our HS320 / HS321 VFD covers 0.4 to 7.5 kW in both 220 V and 380 V, which is the range this spindle sits in.

Tell us the voltage you have when you ask for a quotation. The 220 V and 380 V builds carry different current figures, and the drive has to be ordered for the same voltage as the spindle.

FAQ

Can it run on 380 V?
Yes. The same spindle is wound for 220 V at 8 A or 380 V at 5 A. The VFD has to match the winding, so state the supply when you order.

What is the largest cutter it takes?
ER20 accepts shanks up to 13 mm. A 12 mm flat cutter is the practical ceiling for a 2.0 kW body in wood and plastics.

Does it include the pump and the drive?
This page is the spindle on its own. Kits that pair the spindle with a VFD and the water circuit are listed separately in this category.

Three bearings or four?
Both builds are made. The four-bearing version carries the 235 mm body and is the one to take for continuous production duty; the three-bearing build is 25 mm shorter.

Related products

GDZ-100-3.7 water cooled spindle 3.7 kW  ·  GDZ-125-5.5 water cooled spindle 5.5 kW  ·  STZ water cooled spindle 0.8-2.2 kW  ·  ER collets and nuts  ·  Ask for a quotation

Hot Tags: 2.0kw water cooled spindle,GDZ80 spindle motor,ER20 water cooled spindle,220V 380V CNC spindle, 2 2 kw spindle vfd, cnc spindle for steel, industrial vfd, pcb milling spindle, second hand vfd drive, vfd for corporate image

Send Inquiry

whatsapp

Phone

E-mail

Inquiry