Nov 13, 2026Leave a message

How to install a gear and rack correctly?

Almost every noisy rack we get asked about was installed carefully. The bolts were tight, the pinion was centred, nothing was forced. What nobody checked was whether the rack itself ran parallel to the guide it was supposed to follow - and that is the one measurement that decides whether the pair lasts a year or five.

The joint is where a rack goes wrong first

Racks arrive in sections. Two sections butted end to end have to share one tooth pitch across the join, and a step of a few hundredths there is enough to hear.

Three things matter at the joint:

  • Stagger the joins. If the machine has two racks running side by side, offset the joints. Lining them up puts both steps under the carriage at the same instant, which doubles the bump.
  • Pin the joint, do not rely on the bolts. A dowel or a machined key across the butt keeps the sections from creeping apart under load. Bolts alone let the gap open over months of reversing.
  • Check the joint with the pinion off. Lay a straight edge across the tooth tips and run a dial indicator along the joint. If the indicator moves, the sections are stepped - fix it now, because once the pinion is on you are measuring a symptom instead of a cause.

A rack that clicks once per pinion revolution at low speed is almost always a joint, not a bad tooth.

Backlash is a setting, not a tolerance you inherit

Backlash is the gap between pinion tooth and rack tooth. It is set at assembly, and it is the second most common cause of trouble.

Too tight and the pair runs hot. The teeth scuff, grease turns dark, and in a badly loaded axis you can feel the motor working harder on one direction than the other. Too loose and you get lost motion: the carriage moves a fraction of a millimetre before anything happens when the axis reverses. On a router that shows up as a mark at every direction change.

There are two ways to get it right.

Fixed centre distance is the simple one. The motor bracket holds the pinion at a set distance from the rack, and you shim the bracket until the mesh feels right. It is repeatable and cheap, but the setting never compensates for wear.

A spring-loaded pinion holds the pinion against the rack with a spring or an eccentric. Backlash stays near zero as the teeth wear, at the cost of a more complicated bracket and a small, constant side load. On long axes with reversing duty, it is usually worth it.

Either way, measure it. Put a dial indicator on the carriage, command a small move in one direction, then reverse and command the same move back. The difference between where it stops and where it should have stopped is your backlash. Do it at both ends of travel, because a rack that was set correctly at one end can be tight at the other if the rail and the rack are not parallel.

info-1-1

Align the rack to the guide, not to the frame

This is the part that gets skipped. The rack does not need to be straight relative to the weldment. It needs to be straight and parallel relative to the linear guide the carriage actually runs on.

Procedure that works:

  • Mount the guide rail first and get it true. Everything downstream references it.
  • Set the rack lightly - snug the bolts but leave them just loose enough to tap the rack sideways.
  • Mount a dial indicator on the carriage, with the stylus on the rack's side face or on a tooth flank, and traverse the full stroke by hand.
  • Tap the rack into line where the indicator swings, working from one end.
  • Torque the bolts in stages, re-checking after each pass. Racks move when the bolts pull down if the mounting face is not flat.

If you cannot get the indicator to settle, the mounting face is probably not flat, or the rack is bowed from storage. Check the rack on a surface plate before blaming the machine.

Work from the middle outward

When you bolt a long rack down, start at the centre and alternate outward. Working end to end pushes the accumulated error to one side; working outward from the centre pushes it to both ends, where the pinion spends less time.

Same logic applies to the mounting bolts along a section - snug from the middle, then torque from the middle.

Grease at assembly, and grease the right thing

Put grease on the rack teeth before the pinion ever touches them. A dry first run does more damage than a year of running lightly greased.

Use a grease that stays put on a vertical or inverted rack. If the rack faces down, a heavy-bodied grease with good adhesion beats a thin one that drips off overnight. We go through the lubrication side on the HGR linear guide maintenance article, because on most machines the rack and the rail want the same attention at the same service interval.

Commissioning: what to listen for

Run the full stroke by hand before you power the axis. Then run it under power at low speed, then at working speed, then reverse repeatedly.

What you notice Most likely cause Check first

Click once per pinion revolution | Joint step between rack sections | Straight edge and indicator across the joint Click once per tooth | Damaged or burred tooth, or trapped swarf | Tooth flanks near the pinion at that position Growl that rises with speed | Mesh too tight, or too little grease | Backlash measurement and grease film Lost motion on reversal | Backlash too loose, or a loose pinion on its shaft | Indicator on carriage, then on pinion vs shaft Vibration only at one end of travel | Rack not parallel to the guide | Indicator traverse over full stroke Wear concentrated on one flank | Pinion offset or the pair running at an angle | Contact pattern with marking compound

That last row is worth doing once on any new installation. Paint the pinion teeth with marking compound, run the axis a short distance under light load, and look at where the contact lands. A centred pattern across the tooth height means the pair is running true. A pattern riding high or low means the centre distance is wrong. A pattern skewed along the tooth means the pinion is not square to the rack - and that pair will wear into a wedge shape before it fails.

What to send when a rack is noisy

A recording helps more than a description, honestly. Beyond that: the module and tooth count if known, the rack length and how many sections, whether the machine is new or has been running, and a photo of the tooth contact area.

If the machine is new and has never run properly, suspect installation. If it ran quietly for two years and started clicking last month, suspect the joint has opened or the mounting bolts have relaxed. Different problems, different fixes - and worth telling apart before you order a replacement rack.

The CNC gear rack range covers the module and tooth counts we cut, and if the axis needs reduction anyway the gear box options mount between the motor and the pinion. For the tooth-count arithmetic itself - how many teeth for a given travel per revolution - that is a separate calculation and it is on the teeth selection guide page. Get that number right before you order, because installation cannot fix a pinion that is the wrong size for the axis.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry